FORD

FORD DCU10X tuning

Officially supported in DaVinci Deluxe. Our software performs the following services on this ECU:

ACTIVE GRILL SHUTTER (AGS)ADBLUEBOOST INCREASECOLD START DELETECYLINDER ON DEMAND OFFDEEP IDLEDEEP IDLE ( VGT )DEEP IDLE ( VGT ) 1000 RPMDEEP IDLE ( VGT ) 1200 RPMDEEP IDLE ( VGT ) 1500 RPMDEEP IDLE ( VGT ) 850 RPMDPFDTC OFFECO TUNEEGREGT OFFEVAPFCA UNLOCKFLAPS (SWIRL)GEARBOX TUNINGGLOW PLUGHARDCUTHARDCUT (FLAMES)HOT START FIXHOTSTARTIGNITION CUTIMMO OFF (EPROM)IMMO OFF (FLASH)INJECTOR QUANTITY TUNINGLAMBDALAUNCH CONTROL ACTIVATIONMAFMULTIMAPNOXOIL PRESSURE FIXRAIL PRESSURE TUNINGREADINESS CALIBRATIONREV LIMITER RAISERPM SOFT LIMITER REMOVALSAPSMOKE LIMITER OFFSPORT DISPLAYS CALIBRATIONSTAGE1STAGE1+STAGE2STAGE2+STAGE3START-STOPTORQUE MONITORTPROTTVAVMAXWATER PUMP
See pricing →

What can DaVinci Deluxe do on the FORD DCU10X?

  • ACTIVE GRILL SHUTTER (AGS) — Supported service.
  • ADBLUE — Disable the AdBlue / SCR urea injection requirement when the system is broken.
  • BOOST INCREASE — Supported service.
  • COLD START DELETE — Supported service.
  • CYLINDER ON DEMAND OFF — Supported service.
  • DEEP IDLE — Supported service.
  • DEEP IDLE ( VGT ) — Supported service.
  • DEEP IDLE ( VGT ) 1000 RPM — Supported service.
  • DEEP IDLE ( VGT ) 1200 RPM — Supported service.
  • DEEP IDLE ( VGT ) 1500 RPM — Supported service.
  • DEEP IDLE ( VGT ) 850 RPM — Supported service.
  • DPF — Disable diesel particulate filter regen cycles and warnings.
  • DTC OFF — Supported service.
  • ECO TUNE — Supported service.
  • EGR — Block exhaust gas recirculation valve and disable the corresponding fault codes.
  • EGT OFF — Supported service.
  • EVAP — Supported service.
  • FCA UNLOCK — Supported service.
  • FLAPS (SWIRL) — Supported service.
  • GEARBOX TUNING — Supported service.
  • GLOW PLUG — Supported service.
  • HARDCUT — Hard cut rev limiter, ideal for performance setups.
  • HARDCUT (FLAMES) — Supported service.
  • HOT START FIX — Supported service.
  • HOTSTART — Supported service.
  • IGNITION CUT — Supported service.
  • IMMO OFF (EPROM) — Supported service.
  • IMMO OFF (FLASH) — Supported service.
  • INJECTOR QUANTITY TUNING — Supported service.
  • LAMBDA — Lambda / O2 sensor monitoring removal after CAT delete.
  • LAUNCH CONTROL ACTIVATION — Supported service.
  • MAF — Mass airflow sensor virtualisation.
  • MULTIMAP — Supported service.
  • NOX — NOx sensor delete to bypass failed/expensive sensors.
  • OIL PRESSURE FIX — Supported service.
  • RAIL PRESSURE TUNING — Supported service.
  • READINESS CALIBRATION — Supported service.
  • REV LIMITER RAISE — Supported service.
  • RPM SOFT LIMITER REMOVAL — Supported service.
  • SAP — Supported service.
  • SMOKE LIMITER OFF — Supported service.
  • SPORT DISPLAYS CALIBRATION — Supported service.
  • STAGE1 — Supported service.
  • STAGE1+ — Supported service.
  • STAGE2 — Supported service.
  • STAGE2+ — Supported service.
  • STAGE3 — Supported service.
  • START-STOP — Supported service.
  • TORQUE MONITOR — Supported service.
  • TPROT — Supported service.
  • TVA — Throttle valve / swirl flap delete.
  • VMAX — Supported service.
  • WATER PUMP — Supported service.

Need Stage 1 / Stage 2 / Pops & Bangs on this ECU? These performance services are done via Cloud Tuning, not inside the desktop software.

How to start

  1. Pick your DaVinci Deluxe plan (Standard 299€ lifetime, Pro 499€ lifetime, Monthly 100.99€, Yearly 1009€).
  2. Read the BIN from your DCU10X via OBD or bench.
  3. Open it in DaVinci Deluxe, toggle the services above, save the patched BIN, flash it back.
  4. Done in minutes. Checksum auto-corrected.
← Back to all supported ECUs